[parisc-linux] Apollo 700 serie 9000/720 already problems !
Christoph Plattner
christoph.plattner@dot.at
Tue, 16 Jan 2001 23:48:50 +0100
Hi PA-RISC hackers !
I already have problems booting my HP apollo 700 serie (Model 720,
with 50MHz, 64MB RAM).
I build a new cross-compiler tool chain plus glibc-2, and already
was perfect. It was the snap shot of the Jan-13-2000. I also build
the kernel + lifimage. First of all I discovered the kernel crash
after or while parallel port init (also mentioned in your list for
the 735 model). So I configured it out, so my kernel continous booting.
The SCSI probing has a problem with the device ID0, a floppy on a
SCSI adapter. Ok, forget it. Then the kernel continous booting.
The kernel does a bootp and gets the answer from the server, then
it successfully mounts the NFS root, but by booting the init or
any other tool I tried I see the folloing error:
:
:
Looking up port of RPC 100005/2 on 196.1.1.20
VFS: Mounted root (nfs filesystem) readonly.
Warning: unable to open an initial console.
handle_interruption() pid=1 command='init'
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00000000000001001000000100001011
r0-3 00000000 40019b48 40002dfb 40001504
r4-7 40019b48 40000384 4000ec30 400198f4
r8-11 bb000148 40002d4c 400002f4 00000000
r12-15 00000081 00000080 bb0002f0 bb000048
r16-19 00000000 c02a0640 00000000 40019b48
r20-23 00000041 40000000 40000000 00000000
r24-27 40000000 00000001 bb000148 c011a800
r28-31 00000021 bb000148 bb0003c0 40002daf
sr0-3 00000000 00000000 00000000 0000ffff
sr4-7 00000001 00000001 00000001 00000001
IASQ: 00000001 00000001 IAOQ: 40003393 40003397
IIR: 0ce61280 ISR: 00000001 IOR: 400198f4
ORIG_R28: 00000000
:
:
Can you give me a short explanation of this dump.
On the HP I don't know the registers (on intel I do !).
Which describes the instrunction pointer to have a look
in the System.map. Is this IIR ?
The init I tried (the last attempt) was a fresh build `init'
from the init-2.77 package with the cross compiler by setting
the CC= varibale. The build could be done and a check with the
command `file' described the correct image.
What is this for a problem ???
I will add the complete boot log below.
Trying scsi.4.0
Boot path initialized.
Attempting to load IPL.
Hard booted.
palo ipl root@didymos.pladom1.at Sun Jan 14 12:44:07 CET 2001
0/vmlinux 2106807 bytes @ 0x6800
0/palo-cmdline '0/vmlinux HOME=/ TERM=linux root=/dev/nfs
nfsroot=196.1.1.20:/tf
tpboot/apollo/root console=ttyS0'
Kernel: partition 0 file /vmlinux
ELF32 executable
Entry 00100150 first 00000000 n 3
Segment 0 load 00000000 size 288 mediaptr 0x1000
Segment 1 load 00100000 size 1409924 mediaptr 0x2000
Segment 2 load 0025a000 size 294912 mediaptr 0x15b000
branching to kernel entry point 0x00100150
PDC Console Initialized
The 32-bit Kernel has started...
Enabled FP coprocessor
Free memory starts at: 0xc02cb000
start_parisc(0x504d70,0x504d70,0x0,0x0)
PALO command line: 'HOME=/ TERM=linux root=/dev/nfs
nfsroot=196.1.1.20:/tftpboot
/apollo/root console=ttyS0'
PALO initrd 0-0
model 00002000 00000481 00000000 00000000 0234072e 000011f4 00000004
0000000d
00000000
vers 00000003
CPUID vers 0 rev 0
model 9000/720
led_init: CPU_HVERSION 200
Searching for devices in PDC firmware... processor hpa 0xfffbe000
an older box...
Found devices:
1. Coral SGC Graphics (10) at 0xf8000000, versions 0x4, 0x0, 0x77, 0x0,
0x0
2. Cobra Core BA (11) at 0xf082f000, versions 0x4, 0x0, 0x70, 0x0, 0x0
3. Cobra Core SCSI (10) at 0xf0825000, versions 0x4, 0x0, 0x71, 0x0, 0x0
4. Cobra Core LAN (802.3) (10) at 0xf0826000, versions 0x4, 0x0, 0x72,
0x0, 0x0
5. Cobra Core HIL (10) at 0xf0821000, versions 0x4, 0x0, 0x73, 0x0, 0x0
6. Cobra Core RS-232 (10) at 0xf0823000, versions 0x4, 0x0, 0x75, 0x0,
0x0
7. Cobra Core RS-232 (10) at 0xf0822000, versions 0x4, 0x0, 0x75, 0x0,
0x0
8. Cobra Core Centronics (10) at 0xf0824000, versions 0x4, 0x0, 0x74,
0x0, 0x0
9. Cobra (720) (0) at 0xfffbe000, versions 0x200, 0x0, 0x4, 0x0, 0x81
10. Cobra (1) at 0xfffbf000, versions 0x13, 0x0, 0x9, 0x0, 0x0
That's a total of 10 devices.
CPU(s): 1 x PA7000 (PCX-S) at 50.000000 MHz
Linux version 2.4.0-test10 (root@didymos.pladom1.at) (gcc version 2.96
20000925
(experimental)) #2 Sun Jan 14 13:11:36 CET 2001
free_bootmem(0x2cb800, 0x3d34800)
initrd: 00000000-00000000
pagetable_init
On node 0 totalpages: 16384
zone(0): 8192 pages.
zone(1): 8192 pages.
zone(2): 0 pages.
Kernel command line: HOME=/ TERM=linux root=/dev/nfs
nfsroot=196.1.1.20:/tftpboot/apollo/root console=ttyS0
trap_init
Error reading tod clock
Calibrating delay loop... 49.77 BogoMIPS
Memory: 61512k available
Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
ASP version 1 at 0xf0800000 found.
LED (ASP-style) display at 00000000 registered
Found i82596 at 0xf0826000, IRQ 87
early initialization of device eth0 is deferred
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: enabling 8 loop devices
82596.c: MAC of HP700 LAN blindely read from the prom!
eth0: Couldn't get consistent shared memory
eth0: 82596 at 0xf0826000, 08 00 09 24 64 06 IRQ 87.
82596.c $Revision: 1.14 $
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ
SERIAL_PCI ena
bled
ttyS00 at iomem 0xf0823800 (irq = 90) is a 16550A
ttyS01 at iomem 0xf0822800 (irq = 89) is a 16550A
Generic RTC Driver v1.02 05/27/1999 Sam Creasey (sammy@oh.verio.com)
SCSI subsystem driver Revision: 1.00
sim700: Couldn't get consistent shared memory
sim700: Configuring 53c700 (SCSI-ID 7) at f0825100, IRQ 86
scsi0: Revision 0x0
Post test1, istat 05, sstat0 00, dstat 84
sim700: WARNING IRQ probe failed, (returned 0)
scsi0: WARNING: target data areas are not dma coherent!
scsi0: test 1 completed ok.
scsi0 : LASI/Simple 53c7xx
scsi0: Unable to abort command for target 0
scsi0: Unable to send Bus Device Reset for target 0
scsi0: Unable to do SCSI bus reset
scsi0: >>>>>>>>>>>> Host reset <<<<<<<<<<<<
scsi0: istat = 0c, sstat0 = 00, sstat1 = 00, dstat = 00
scsi0: dsp = 03f98058 (script[0x0016]), dsps = 03f98cee, target = 0
scsi0: Failing command for ID0
scsi0: Unable to abort command for target 0
scsi0: Unable to abort command for target 1
scsi0: Unable to send Bus Device Reset for target 1
scsi0: Unable to do SCSI bus reset
scsi0: >>>>>>>>>>>> Host reset <<<<<<<<<<<<
scsi0: istat = 0c, sstat0 = 00, sstat1 = 00, dstat = 00
scsi0: dsp = 03f98058 (script[0x0016]), dsps = 03f98cee, target = 0
scsi0: Failing command for ID0
Vendor: SEAGATE Model: ST1480 SUN0424 Rev: 7516
Type: Direct-Access ANSI SCSI revision: 02
Vendor: QUANTUM Model: PD425S Rev: 535A
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 4, lun 0
Detected scsi disk sdb at scsi0, channel 0, id 6, lun 0
SCSI device sda: 843284 512-byte hdwr sectors (432 MB)
Partition check:
sda: unknown partition table
SCSI device sdb: 833150 512-byte hdwr sectors (427 MB)
sdb: unknown partition table
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
eth0: link ok.
Sending BOOTP requests.... OK
IP-Config: Got BOOTP answer from 196.1.1.20, my address is 196.1.1.110
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kmem_create: Forcing size word alignment - nfs_fh
Looking up port of RPC 100003/2 on 196.1.1.20
Looking up port of RPC 100005/2 on 196.1.1.20
VFS: Mounted root (nfs filesystem) readonly.
Warning: unable to open an initial console.
handle_interruption() pid=1 command='init'
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00000000000001001000000100001011
r0-3 00000000 40019b48 40002dfb 40001504
r4-7 40019b48 40000384 4000ec30 400198f4
r8-11 bb000148 40002d4c 400002f4 00000000
r12-15 00000081 00000080 bb0002f0 bb000048
r16-19 00000000 c02a0640 00000000 40019b48
r20-23 00000041 40000000 40000000 00000000
r24-27 40000000 00000001 bb000148 c011a800
r28-31 00000021 bb000148 bb0003c0 40002daf
sr0-3 00000000 00000000 00000000 0000ffff
sr4-7 00000001 00000001 00000001 00000001
IASQ: 00000001 00000001 IAOQ: 40003393 40003397
IIR: 0ce61280 ISR: 00000001 IOR: 400198f4
ORIG_R28: 00000000
handle_interruption() pid=1 command='init'
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00000000000001001000000100001011
r0-3 00000000 40019b48 40002dfb 40001504
r4-7 40019b48 40000384 4000ec30 400198f4
r8-11 bb000148 40002d4c 400002f4 00000000
r12-15 00000081 00000080 bb0002f0 bb000048
r16-19 00000000 c02a0640 00000000 40019b48
r20-23 00000041 40000000 40000000 00000000
r24-27 40000000 00000001 bb000148 c011a800
r28-31 00000021 bb000148 bb0003c0 40002daf
sr0-3 00000000 00000000 00000000 0000ffff
sr4-7 00000001 00000001 00000001 00000001
IASQ: 00000001 00000001 IAOQ: 40003393 40003397
IIR: 0ce61280 ISR: 00000001 IOR: 400198f4
ORIG_R28: 00000000
:
:
: ... and so on ...
-------------------------------------------------------------------------
private: christoph.plattner@dot.at
company: christoph.plattner@alcatel.at