[parisc-linux] RE: X windows setup on C110 with woody and kernel-2.4.20pa22
Mehta, Miten
mmehta@elgin.edu
Wed, 29 Jan 2003 16:12:12 -0600
This message is in MIME format. Since your mail reader does not understand
this format, some or all of this message may not be legible.
------_=_NextPart_000_01C2C7E3.790A7FB0
Content-Type: text/plain;
charset="iso-8859-1"
Hey,
I tried it again and find here xfree log. I was advised to take X window
setup to debian-hppa so I did not post to parisc list. Also find
XF86Config-4.
Actually what I just did I had done that in very first attempt ;-). Thibaut
VARENE pointed out some thing which I have not tried to use /dev/psaux in
place of /dev/input/mice. Just shall wait for your reponse.
thanks.
Miten.
-----Original Message-----
From: Helge Deller [mailto:deller@gmx.de]
Sent: Wednesday, January 29, 2003 1:57 PM
To: Mehta, Miten
Cc: parisc-linux@lists.parisc-linux.org
Subject: Re: X windows setup on C110 with woody and kernel-2.4.20pa22
Hi Miten,
Please don't remove parisc-linux@lists.parisc-linux.org from the receivers
in the future.
>From your dmesg this is the important part:
STI GSC/PCI graphics driver version 0.9
STI byte mode ROM at f4000000, hpa at f4000000
STI id 2bcb015a-9a02587, conforms to spec rev. 8.04
STI device: HPA4071B
Console: switching to colour frame buffer device 160x64
fb0: stifb 1280x1024-32 frame buffer device, id: 2bcb015a, mmio: 0xf4100000
So, if you change the in SubSection "Display" the Depth to 32 it should
work:
Example:
SubSection "Display"
Depth 32 # 8, 16, 24 or 32 (acording
to "fbset -i")
Modes "1280x1024" # "1024x768" or "1280x1024"
EndSubSection
You don't seem to have HIL, but IIRC the ps/2 driver uses the same
/dev/input/mice
interface.
Regards,
Helge
------_=_NextPart_000_01C2C7E3.790A7FB0
Content-Type: application/octet-stream;
name="XFree86.0.log"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: attachment;
filename="XFree86.0.log"
This is a pre-release version of XFree86, and is not supported in any
way. Bugs may be reported to XFree86@XFree86.Org and patches submitted
to fixes@XFree86.Org. Before reporting bugs in pre-release versions,
please check the latest version in the XFree86 CVS repository
(http://www.XFree86.Org/cvs)
XFree86 Version 4.1.0.1 / X Window System
(protocol Version 11, revision 0, vendor release 6510)
Release Date: 21 December 2001
If the server is older than 6-12 months, or if your card is
newer than the above date, look for a newer version before
reporting problems. (See http://www.XFree86.Org/FAQ)
Build Operating System: Linux 2.4.16-64 parisc64 [ELF]=20
(=3D=3D) Log file: "/var/log/XFree86.0.log", Time: Wed Jan 29 22:13:09 =
2003
(=3D=3D) Using config file: "/etc/X11/XF86Config-4"
Markers: (--) probed, (**) from config file, (=3D=3D) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(=3D=3D) ServerLayout "Default Layout"
(**) |-->Screen "Default Screen" (0)
(**) | |-->Monitor "Generic Monitor"
(**) | |-->Device "Generic Video Card"
(**) |-->Input Device "Keyboard"
(=3D=3D) Keyboard: CustomKeycode disabled
(**) |-->Input Device "Mouse"
(WW) The directory "/usr/lib/X11/fonts/cyrillic" does not exist.
Entry deleted from font path.
(**) FontPath set to =
"unix/:7100,/usr/lib/X11/fonts/misc,/usr/lib/X11/fonts/100dpi/:unscaled,=
/usr/lib/X11/fonts/75dpi/:unscaled,/usr/lib/X11/fonts/Type1,/usr/lib/X11=
/fonts/Speedo,/usr/lib/X11/fonts/100dpi,/usr/lib/X11/fonts/75dpi"
(=3D=3D) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(--) using VT number 7
(WW) Cannot open APM
(EE) No OS PCI support available
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x00000000 - 0x00000000 (0x1) MX[B]
[2] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[3] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x00000000 - 0x00000000 (0x1) MX[B]
[2] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[3] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x00000000 - 0x00000000 (0x1) MX[B]
[2] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[3] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) MGA: driver for Matrox chipsets: mga2064w, mga1064sg, mga2164w,
mga2164w AGP, mgag100, mgag100 PCI, mgag200, mgag200 PCI, mgag400
(II) GLINT: driver for 3Dlabs chipsets: gamma, ti_pm2, ti_pm, pm3, =
pm2v,
pm2, pm, 300sx, 500tx, mx, delta
S3VIdentify
(II) S3VIRGE: driver (version 1.6.13) for S3 ViRGE chipsets: virge, =
86C325,
virge vx, 86C988, virge dx, virge gx, 86C375, 86C385, virge gx2,
86C357, virge mx, 86C260, virge mx+, 86C280, trio 3d, 86C365,
trio 3d/2x, 86C362, 86C368
(II) SIS: driver for SiS chipsets: SIS5597, SIS5598, SIS530, SIS6326,
SIS300, SIS630, SIS540
(II) SAVAGE: driver (version 1.1.16) for S3 Savage chipsets: Savage4,
Savage3D, Savage3D-MV, Savage2000, Savage/MX-MV, Savage/MX,
Savage/IX-MV, Savage/IX, ProSavage PM133, ProSavage KM133, Twister,
TwisterK
(II) TRIDENT: driver for Trident chipsets: tvga8900d, cyber9320, =
cyber9388,
cyber9397, cyber9397dvd, cyber9520, cyber9525dvd, cyberblade/e4,
tgui9420dgi, tgui9440agi, tgui9660, tgui9680, providia9682,
providia9685, cyber9382, cyber9385, 3dimage975, 3dimage985, blade3d,
cyberbladei7, cyberbladei7d, cyberbladei1, cyberbladei1d,
cyberbladeAi1, cyberbladeAi1d, cyberbladeXP, cyberbladeXPm
(II) CHIPS: Driver for Chips and Technologies chipsets: ct65520, =
ct65525,
ct65530, ct65535, ct65540, ct65545, ct65546, ct65548, ct65550,
ct65554, ct65555, ct68554, ct69000, ct69030, ct64200, ct64300
(II) TDFX: Driver for 3dfx Banshee/Voodoo3 chipsets: 3dfx Banshee,
3dfx Voodoo3, 3dfx Voodoo5
(II) FBDev: driver for framebuffer: fbdev, afb
(II) ATI: ATI driver (version 6.3.6) for chipsets: ati
(II) R128: Driver for ATI Rage 128 chipsets: ATI Rage 128 RE (PCI),
ATI Rage 128 RF (AGP), ATI Rage 128 RG (AGP), ATI Rage 128 RK (PCI),
ATI Rage 128 RL (AGP), ATI Rage 128 Pro PD (PCI),
ATI Rage 128 Pro PF (AGP), ATI Rage 128 Pro PP (PCI),
ATI Rage 128 Pro PR (PCI), ATI Rage 128 Mobility LE (PCI),
ATI Rage 128 Mobility LF (AGP), ATI Rage 128 Mobility MF (AGP),
ATI Rage 128 Mobility ML (AGP)
(II) RADEON: Driver for ATI Radeon chipsets: ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
ATI Radeon VE (AGP)
(II) imstt: driver (version 1.0.0 for IMS TwinTurbo chipsets : =
imstt128,
imstt3d
(II) VGA: Generic VGA driver (version 4.0) for chipsets: generic
(II) v4l driver for Video4Linux
S3VProbe begin
(II) FBDev(0): using default device
(II) Running in FRAMEBUFFER Mode
(EE) FBDev(0): No Display subsection in Screen section "Default Screen" =
for depth/fbbpp 24/24
(EE) Screen(s) found, but none have a usable configuration.
Fatal server error:
no screens found
When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to submit@bugs.debian.org.
------_=_NextPart_000_01C2C7E3.790A7FB0
Content-Type: application/octet-stream;
name="XF86Config-4"
Content-Disposition: attachment;
filename="XF86Config-4"
#
# This XFree86 config files is usable for HIL and USB keyboards and mice
# by Helge Deller <deller@gmx.de> 2002-07-06
#
# Please adjust the "depth" and "Modes" entries below in the Screen Section
# acording to your system configuration.
#
# EXAMPLE:
# Run the following command on the bash prompt:
#
# dmesg | grep stifb
#
# and my system gives:
# fb0: stifb 1280x1024-8 frame buffer device, id: 2b4ded6d, mmio: 0xf8100000
# so I'm using "Depth 8" and "Modes 1280x1024" below.
#
Section "Files"
FontPath "unix/:7100" # local font server
# if the local font server has problems, we can fall back on these
FontPath "/usr/lib/X11/fonts/misc"
FontPath "/usr/lib/X11/fonts/cyrillic"
FontPath "/usr/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/lib/X11/fonts/Type1"
FontPath "/usr/lib/X11/fonts/Speedo"
FontPath "/usr/lib/X11/fonts/100dpi"
FontPath "/usr/lib/X11/fonts/75dpi"
EndSection
Section "Module"
Load "GLcore"
Load "bitmap"
Load "dbe"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "pex5"
Load "record"
Load "speedo"
Load "type1"
Load "vbe"
Load "xie"
EndSection
Section "InputDevice"
Identifier "Keyboard"
Driver "keyboard"
Option "CoreKeyboard"
# Option "XkbLayout" "de"
EndSection
Section "InputDevice"
Identifier "Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
EndSection
Section "Device"
Identifier "Generic Video Card"
Driver "fbdev"
Option "UseFBDev" "true"
EndSection
Section "Monitor"
Identifier "Generic Monitor"
HorizSync 30-70
VertRefresh 50-160
Option "DPMS"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "Generic Video Card"
Monitor "Generic Monitor"
SubSection "Display"
Depth 32 # 8, 16, 24 or 32
Modes "1280x1024" # "1024x768" or "1280x1024"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "Keyboard"
InputDevice "Mouse"
EndSection
Section "DRI"
Mode 0666
EndSection
------_=_NextPart_000_01C2C7E3.790A7FB0--