[parisc-linux] Booting C200
Herb Radford
herbr@magma.ca
Mon, 05 Nov 2001 07:16:36 -0500
OK, I found some stuff in the archive on the "Chassis Codes" and set up an
old laptop as a terminal, disconnected the keyboard (and mouse) and booted.
Now I tried this with the disk out of my 712/60 and the C200 is not hung.
It proceeds through the boot process and then hangs on starting cron.
>From the console log, I cannot find any mention of a graphics card so I
would assume that the A4553A is not supported/handled correctly. Is there a
graphics card which is "supported"? I don't know if I can get my hands on
another graphics card (other than the A4070A in the C110).
I'll try the "Chassis Codes" thing on the C110 and send the log.
Here's the log from my attempt. Note that I had shut down by pulling the AC
when the box hung so I had to fsck the partition manually:
TEST 2023
TEST 2030
TEST 2040
TEST 2060
TEST 2070
TEST 2071
TEST 2072
TEST 2073
TEST 2074
TEST 2080
TEST 10B1
INIT 103C
TEST 103E
INIT C30C
INIT 10CA
INIT C30C
INIT 10CA
INIT CD00
INIT CD08
TEST CD10
INIT CD10
TEST CD11
TEST CD12
TEST CD13
TEST CD14
TEST CD15
TEST CD1F
INIT CD1F
TEST CD1A
TEST CD1B
TEST CD1C
TEST CD1D
TEST CD20
INIT CD20
TEST CD21
TEST CD22
TEST CD23
TEST CD24
TEST CD25
TEST CD2A
TEST CD2B
TEST CD2C
TEST CD2D
TEST CD16
INIT CDFF
TEST C210
TEST C220
TEST C230
TEST C2D3
TEST C2D7
TEST C240
TEST C260
TEST C261
TEST C263
TEST C264
TEST C265
TEST C2E0
INIT C30C
INIT 10CA
TEST 4000
TEST 4020
TEST 4021
TEST 4021
TEST 4022
TEST 4022
TEST 4023
TEST 4023
TEST 4024
TEST 4024
TEST 4025
TEST 4025
TEST 4026
TEST 4026
TEST 4029
TEST 4029
TEST 402A
TEST 402A
TEST 402D
TEST 402D
TEST 4030
TEST 4040
TEST 4050
TEST 4060
TEST 2090
TEST 2050
TEST 10B2
TEST 10A0
TEST 10A1
TEST 10A2
TEST 10A3
TEST 10A4
TEST 10A5
INIT 103C
TEST 400E
INIT C30C
INIT 10CA
INIT C3FF
INIT C30C
INIT 10CA
INIT 8C20
INIT 8C21
INIT 8C22
INIT 8C10
INIT 8C11
INIT 8C12
TEST 301B
TEST 301C
INIT C653
INIT C400
INIT C440
INIT C642
WARN 80F4
WARN 9000
INIT C641
INIT C642
WARN 80F4
INIT C605
INIT C600
INIT C640
Firmware Version 5.0
Duplex Console IO Dependent Code (IODC) revision 1
----------------------------------------------------------------------------
--
(c) Copyright 1995-1998, Hewlett-Packard Company, All rights reserved
---------------------------------------------------------------------------
---
Processor Speed State Coprocessor State I/D Cache
--------- -------- --------------------- -----------------
-------------
0 200 MHz Active Functional 512 KB/1 MB
Central Bus Speed (in MHz) : 120
Available memory (bytes) : 268435456
Good memory required (bytes): 22343680
Primary boot path: FWSCSI.6.0
Alternate boot path: SESCSI.5.0
Console path: GRAPHICS(4)
Keyboard path: PS2
------- Main Menu
-------------------------------------------------------------
Command Description
------- -----------
BOot [PRI|ALT|<path>] Boot from specified path
PAth [PRI|ALT|CON|KEY] [<path>] Display or modify a path
SEArch [DIsplay|IPL] [<path>] Search for boot devices
COnfiguration [<command>] Access Configuration menu/commands
INformation [<command>] Access Information menu/commands
SERvice [<command>] Access Service menu/commands
DIsplay Redisplay the current menu
HElp [<menu>|<command>] Display help for menu or command
RESET Restart the system
-------
Main Menu: Enter command > sea ipl
Searching for device(s) with bootable media...
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path Device Type and Utilities
----------- ----------------- -------------------------
P0 SESCSI.6.0 SEAGATE ST31230N
IPL
Search terminated.
Main Menu: Enter command > bo p0
Interact with IPL (Y, N, Q)?> n
INIT C740
Booting...
Boot IO Dependent Code (IODC) revision 153
INIT C780
INIT C30C
INIT 10CA
HARD Booted.
INIT C7FF
palo ipl 0.92 bame@c3k Wed Jun 20 11:49:11 MDT 2001
0/vmlinux32 2853588 bytes @ 0x48000
Partition Start(MB) End(MB) Id Type
1 1 9 f0 Palo
2 10 131 82 swap
3 132 227 83 ext2
4 228 1001 83 ext2
Command line: 'root=/dev/sda3 HOME=/ console=ttyS0 TERM=vt102'
Kernel: partition 3 file /boot/vmlinux-2.4.0
ext2 block size 1024
ext2_mount(partition 3) returns 0
ext2_open(/boot/vmlinux-2.4.0) = 3
ELF32 executable
Entry 00100000 first 00100000 n 4
Segment 0 load 00100000 size 1606948 mediaptr 0x1000
Segment 1 load 0028a000 size 468472 mediaptr 0x18a000
Segment 2 load 00300000 size 8192 mediaptr 0x1fd000
Segment 3 load 0034bea8 size 80688 mediaptr 0x1ffea8
branching to kernel entry point 0x00100000
Set default PSW W bit to 0
Linux version 2.4.0-32 (root@slab) (gcc version 3.0 (Debian)) #1 Thu Jun
28 11:49:00 BST 2001
FP[0] enabled: Rev 0 Model 14
The 32-bit Kernel has started...
Determining PDC firmware type: Newer Box
model 000059d0 00000481 00000000 00000002 77ac21d7 100000f0 00000008
000000b2 000000b2
vers 00000400
cpuid 000001d0
CPUID vers 14 rev 16
model 9000/782/C200+
Total Memory: 256 Mb
On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): 0 pages.
zone(2): 0 pages.
PDC reported no LCD or LED.
Searching for devices...
Found devices:
1. Raven U/L2 Dino RS-232 (10) at 0xf2003000, versions 0x6, 0x0, 0x8c,
0x0, 0x0
2. Raven+ w SE FWSCSI Core BA (11) at 0xffd00000, versions 0x56, 0x0,
0x81, 0x0, 0x0, additional addresses: 0xffd0c000 0xffc00000
3. Raven+ w SE FWSCSI Core RS-232 (10) at 0xffd05000, versions 0x56, 0x0,
0x8c, 0x0, 0x0
4. Raven+ w SE FWSCSI Core SCSI (10) at 0xffd06000, versions 0x56, 0x0,
0x82, 0x0, 0x0
5. Raven+ w SE FWSCSI Core Centronics (10) at 0xffd02000, versions 0x56,
0x0, 0x74, 0x0, 0x0, additional addresses: 0xffd01000 0xffd03000
6. Raven+ w SE FWSCSU Core Audio (10) at 0xffd04000, versions 0x56, 0x4,
0x7b, 0x0, 0x0
7. Raven+ w SE FWSCSI Core PS/2 Port (10) at 0xffd08000, versions 0x56,
0x0, 0x84, 0x0, 0x0
8. Raven+ w SE FWSCSI Core PS/2 Port (10) at 0xffd08100, versions 0x56,
0x0, 0x84, 0x0, 0x0
9. U2-IOA BC GSC+ Port (7) at 0xf203f000, versions 0x501, 0x1, 0xc, 0x3, 0x0
10. U2-IOA BC GSC+ Port (7) at 0xf103f000, versions 0x501, 0x1, 0xc, 0x3, 0x0
11. Cujo PCI Bridge (13) at 0xf1000000, versions 0x682, 0x1, 0xa, 0x1,
0x0, additional addresses: 0xf1800000 0xf6000000
12. Dino PCI Bridge (13) at 0xf2000000, versions 0x680, 0x2, 0xa, 0x0,
0x0, additional addresses: 0xf2800000
13. U2-IOA BC Runway Port (12) at 0xfff88000, versions 0x580, 0xf, 0xb,
0x1, 0x50
14. U2-IOA BC Runway Port (12) at 0xfff8a000, versions 0x580, 0xf, 0xb,
0x1, 0x50
15. Raven U 200 (9000/780/C200) (0) at 0xfffa0000, versions 0x59d, 0x0,
0x4, 0x0, 0x81
16. Raven U 200 (1) at 0xfffb1000, versions 0x5d, 0x0, 0x9, 0x0, 0x0
That's a total of 16 devices.
CPU(s): 1 x PA8200 (PCX-U+) at 200.000000 MHz
Kernel command line: root=/dev/sda3 HOME=/ console=ttyS0 TERM=vt102
Console: colour dummy device 160x64
Calibrating delay loop... 398.95 BogoMIPS
Memory: 255236k available
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
Dino version 3.0 (bridge mode) found at 0xf2000000
The GSCtoPCI (Dino hrev 2) bus converter found may exhibit
data corruption. See Service Note Numbers: A4190A-01, A4191A-01.
Systems shipped after Aug 20, 1997 will not exhibit this problem.
Models affected: C180, C160, C160L, B160L, and B132L workstations.
Lasi version 0 at 0xffd00000 found.
LED display at ffd0c000 registered
PS/2 keyboard controller at 0xffd08000 (irq 133) found, no device attached.
PS/2 psaux controller at 0xffd08100 (irq 133) found, no device attached.
sticonsole_init: searching for STI ROMs
ccio found U2 I/O MMU at 0xfff88000
io_io_high: 0xf6000000 io_io_low: 0xf2000000
ccio found U2 I/O MMU at 0xfff8a000
ccio: Cujo 2.0 bug needs a work around
io_io_high: 0xf2000000 io_io_low: 0xf1000000
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
request_module[parport_lowlevel]: Root fs not mounted
lp: driver loaded but no devices found
RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize
loop: enabling 8 loop devices
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at iomem 0xffd05800 (irq = 154) is a 16550A
ttyS01 at iomem 0xf2003800 (irq = 74) is a 16550A
Generic RTC Driver v1.02 05/27/1999 Sam Creasey (sammy@oh.verio.com)
Linux Tulip driver version 0.9.13 (January 2, 2001)
eth0: Digital DS21143 Tulip rev 48 at 0xff00, 00:60:B0:7D:D8:67, IRQ 64.
eth0: MII transceiver #1 config 1000 status 7809 advertising 01e1.
parport_init_chip: initialize bidirectional-mode.
parport0: PC-style at 0xffd02800, irq 152 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 19, function 0
sym53c8xx: setting PCI_COMMAND_IO PCI_COMMAND_MEMORY...
sym53c8xx: setting PCI_COMMAND_MASTER...(fix-up)
sym53c8xx: 53c875 detected
sym53c875-0: rev 0x4 on pci bus 0 device 19 function 0 irq 67
sym53c875-0: NCR clock is 40401KHz
sym53c875-0: ID 7, Fast-20, Parity Checking
sym53c875-0: on-chip RAM at 0xf2ffe000
sym53c875-0: restart (scsi reset).
sym53c875-0: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx - version 1.6b
sim700: Configuring 53c710 (SCSI-ID 7) at ffd06100, IRQ 150, options 0
scsi1: Revision 0x2
scsi1: test 1 completed ok.
scsi1 : LASI/Simple 53c7xx
Vendor: SEAGATE Model: ST31230N Rev: HP04
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi1, channel 0, id 6, lun 0
SCSI device sda: 2051460 512-byte hdwr sectors (1050 MB)
Partition check:
sda: sda1 sda2 sda3 sda4
Lasi Harmony Audio rev. 16 at 0xffd04000, using IRQ 146
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
IP-Config: Incomplete network configuration information.
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
INIT: version 2.78 booting
Loading /etc/console/boottime.kmap.gz
Activating swap...
Adding Swap: 124800k swap-space (priority -1)
Checking root file system...
Parallelizing fsck version 1.20 (25-May-2001)
/dev/sda3 was not cleanly unmounted, check forced.
/dev/sda3: |=== | 5.8%
/dev/sda3: |======= /
11.7%
/dev/sda3: |==========
- 17.5%
/dev/sda3: |=============
\ 23.3%
/dev/sda3: |================
| 29.2%
/dev/sda3: |====================
/ 35.0%
/dev/sda3: |=======================
- 40.8%
/dev/sda3: |==========================
\ 46.7%
/dev/sda3: |=============================
| 52.5%
/dev/sda3: |=================================
/ 58.3%
/dev/sda3:
|==================================== - 64.2%
/dev/sda3: |======================================= \
70.0%
/dev/sda3: |=========================================
| 73.2%
/dev/sda3: |===========================================
/ 76.9%
/dev/sda3: |==============================================
- 81.4%
/dev/sda3:
|=============================================== \ 84.3%
/dev/sda3: |================================================== |
90.0%
/dev/sda3: |====================================================
/ 92.0%
/dev/sda3:
Unattached inode 4337
/dev/sda3: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
(i.e., without -a or -p options)
fsck failed. Please repair manually and reboot. Please note
that the root file system is currently mounted read-only. To
remount it read-write:
# mount -n -o remount,rw /
CONTROL-D will exit from this shell and REBOOT the system.
Give root password for maintenance
(or type Control-D for normal startup):
(none):~# fsck
Parallelizing fsck version 1.20 (25-May-2001)
(none):~# fsck /dev/sda3
Parallelizing fsck version 1.20 (25-May-2001)
e2fsck 1.20, 25-May-2001 for EXT2 FS 0.5b, 95/08/09
/dev/sda3 contains a file system with errors, check forced.
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Unattached inode 4337
Connect to /lost+found<y>? yes
Inode 4337 ref count is 2, should be 1. Fix<y>? yes
Pass 5: Checking group summary information
Block bitmap differences: -7236 +7316 -8635 +8648 +25426
Fix<y>? yes
Free blocks count wrong for group #0 (842, counted=911).
Fix<y>? yes
Free blocks count wrong for group #3 (57, counted=56).
Fix<y>? yes
Free blocks count wrong (49543, counted=49611).
Fix<y>? yes
Inode bitmap differences: +4337
Fix<y>? yes
Free inodes count wrong for group #2 (1786, counted=1785).
Fix<y>? yes
Free inodes count wrong (21952, counted=21951).
Fix<y>? yes
/dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
/dev/sda3: 2529/24480 files (2.2% non-contiguous), 48019/97630 blocks
(none):~# y shutdown -r now
INIT: Switching to runlevel: 6
(none):~#
INIT: Sending processes the TERM signal
Saving the System Clock time to the Hardware Clock...
hwclock: Could not open file with the clock adjustment parameters in it
(/etc/adjtime) for writing, errno=30: Read-only file system.
Drift adjustment parameters not updated.
Hardware Clock updated to Sun Nov 4 19:37:18 UTC 2001.
Stopping kernel log daemon: klogd.
Stopping system log daemon: syslogd.
Sending all processes the TERM signal... done.
Sending all processes the KILL signal... md: recovery thread got woken up ...
md: recovery thread finished ...
mdrecoveryd(9) flushing signals.
done.
Saving random seed... urandom stop: failed.
done.
Unmounting remote filesystems... done.
Deconfiguring network interfaces: /etc/network/ifstate: Read-only file system
done.
Deactivating swap... done.
Unmounting local filesystems... umount2: Invalid argument
umount: /dev/sda4: not mounted
done.
Rebooting... stopping all md devices.
Restarting system.
INIT C4CC
INIT C4CD
INIT 3002
TEST 30BC
INIT 30BC
TEST C0FF
INIT C30C
INIT 10CA
INIT C300
TEST 1030
TEST 1020
TEST 1021
TEST 1022
TEST 1023
TEST 1024
TEST 1025
TEST 1026
TEST 1027
TEST 1028
TEST 1029
TEST 102A
TEST 102B
TEST 102C
TEST 2010
TEST 2020
TEST 2021
TEST 2022
TEST 2023
TEST 2023
TEST 2030
TEST 2040
TEST 2060
TEST 2070
TEST 2071
TEST 2072
TEST 2073
TEST 2074
TEST 2080
TEST 10B1
INIT 103C
TEST 103E
INIT C30C
INIT 10CA
INIT C30C
INIT 10CA
INIT CD00
INIT CD08
TEST CD10
INIT CD10
TEST CD11
TEST CD12
TEST CD13
TEST CD14
TEST CD15
TEST CD1F
INIT CD1F
TEST CD1A
TEST CD1B
TEST CD1C
TEST CD1D
TEST CD20
INIT CD20
TEST CD21
TEST CD22
TEST CD23
TEST CD24
TEST CD25
TEST CD2A
TEST CD2B
TEST CD2C
TEST CD2D
TEST CD16
INIT CDFF
TEST C210
TEST C220
TEST C230
TEST C2D3
TEST C2D7
TEST C240
TEST C260
TEST C261
TEST C263
TEST C264
TEST C265
TEST C2E0
INIT C30C
INIT 10CA
TEST 4000
TEST 4020
TEST 4021
TEST 4021
TEST 4022
TEST 4022
TEST 4023
TEST 4023
TEST 4024
TEST 4024
TEST 4025
TEST 4025
TEST 4026
TEST 4026
TEST 4029
TEST 4029
TEST 402A
TEST 402A
TEST 402D
TEST 402D
TEST 4030
TEST 4040
TEST 4050
TEST 4060
TEST 2090
TEST 2050
TEST 10B2
TEST 10A0
TEST 10A1
TEST 10A2
TEST 10A3
TEST 10A4
TEST 10A5
INIT 103C
TEST 400E
INIT C30C
INIT 10CA
INIT C3FF
INIT C30C
INIT 10CA
INIT 8C20
INIT 8C21
INIT 8C22
INIT 8C10
INIT 8C11
INIT 8C12
TEST 301B
TEST 301C
INIT C653
INIT C400
INIT C440
INIT C642
WARN 80F4
WARN 9000
INIT C641
INIT C642
WARN 80F4
INIT C605
INIT C600
INIT C640
Firmware Version 5.0
Duplex Console IO Dependent Code (IODC) revision 1
----------------------------------------------------------------------------
--
(c) Copyright 1995-1998, Hewlett-Packard Company, All rights reserved
---------------------------------------------------------------------------
---
Processor Speed State Coprocessor State I/D Cache
--------- -------- --------------------- -----------------
-------------
0 200 MHz Active Functional 512 KB/1 MB
Central Bus Speed (in MHz) : 120
Available memory (bytes) : 268435456
Good memory required (bytes): 22343680
Primary boot path: FWSCSI.6.0
Alternate boot path: SESCSI.5.0
Console path: GRAPHICS(4)
Keyboard path: PS2
------- Main Menu
-------------------------------------------------------------
Command Description
------- -----------
BOot [PRI|ALT|<path>] Boot from specified path
PAth [PRI|ALT|CON|KEY] [<path>] Display or modify a path
SEArch [DIsplay|IPL] [<path>] Search for boot devices
COnfiguration [<command>] Access Configuration menu/commands
INformation [<command>] Access Information menu/commands
SERvice [<command>] Access Service menu/commands
DIsplay Redisplay the current menu
HElp [<menu>|<command>] Display help for menu or command
RESET Restart the system
-------
Main Menu: Enter command > sea ipl
Searching for device(s) with bootable media...
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path Device Type and Utilities
----------- ----------------- -------------------------
P0 SESCSI.6.0 SEAGATE ST31230N
IPL
Search terminated.
Main Menu: Enter command > bo p0
Interact with IPL (Y, N, Q)?> n
INIT C740
Booting...
Boot IO Dependent Code (IODC) revision 153
INIT C780
INIT C30C
INIT 10CA
HARD Booted.
INIT C7FF
palo ipl 0.92 bame@c3k Wed Jun 20 11:49:11 MDT 2001
0/vmlinux32 2853588 bytes @ 0x48000
Partition Start(MB) End(MB) Id Type
1 1 9 f0 Palo
2 10 131 82 swap
3 132 227 83 ext2
4 228 1001 83 ext2
Command line: 'root=/dev/sda3 HOME=/ console=ttyS0 TERM=vt102'
Kernel: partition 3 file /boot/vmlinux-2.4.0
ext2 block size 1024
ext2_mount(partition 3) returns 0
ext2_open(/boot/vmlinux-2.4.0) = 3
ELF32 executable
Entry 00100000 first 00100000 n 4
Segment 0 load 00100000 size 1606948 mediaptr 0x1000
Segment 1 load 0028a000 size 468472 mediaptr 0x18a000
Segment 2 load 00300000 size 8192 mediaptr 0x1fd000
Segment 3 load 0034bea8 size 80688 mediaptr 0x1ffea8
branching to kernel entry point 0x00100000
Set default PSW W bit to 0
Linux version 2.4.0-32 (root@slab) (gcc version 3.0 (Debian)) #1 Thu Jun
28 11:49:00 BST 2001
FP[0] enabled: Rev 0 Model 14
The 32-bit Kernel has started...
Determining PDC firmware type: Newer Box
model 000059d0 00000481 00000000 00000002 77ac21d7 100000f0 00000008
000000b2 000000b2
vers 00000400
cpuid 000001d0
CPUID vers 14 rev 16
model 9000/782/C200+
Total Memory: 256 Mb
On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): 0 pages.
zone(2): 0 pages.
PDC reported no LCD or LED.
Searching for devices...
Found devices:
1. Raven U/L2 Dino RS-232 (10) at 0xf2003000, versions 0x6, 0x0, 0x8c,
0x0, 0x0
2. Raven+ w SE FWSCSI Core BA (11) at 0xffd00000, versions 0x56, 0x0,
0x81, 0x0, 0x0, additional addresses: 0xffd0c000 0xffc00000
3. Raven+ w SE FWSCSI Core RS-232 (10) at 0xffd05000, versions 0x56, 0x0,
0x8c, 0x0, 0x0
4. Raven+ w SE FWSCSI Core SCSI (10) at 0xffd06000, versions 0x56, 0x0,
0x82, 0x0, 0x0
5. Raven+ w SE FWSCSI Core Centronics (10) at 0xffd02000, versions 0x56,
0x0, 0x74, 0x0, 0x0, additional addresses: 0xffd01000 0xffd03000
6. Raven+ w SE FWSCSU Core Audio (10) at 0xffd04000, versions 0x56, 0x4,
0x7b, 0x0, 0x0
7. Raven+ w SE FWSCSI Core PS/2 Port (10) at 0xffd08000, versions 0x56,
0x0, 0x84, 0x0, 0x0
8. Raven+ w SE FWSCSI Core PS/2 Port (10) at 0xffd08100, versions 0x56,
0x0, 0x84, 0x0, 0x0
9. U2-IOA BC GSC+ Port (7) at 0xf203f000, versions 0x501, 0x1, 0xc, 0x3, 0x0
10. U2-IOA BC GSC+ Port (7) at 0xf103f000, versions 0x501, 0x1, 0xc, 0x3, 0x0
11. Cujo PCI Bridge (13) at 0xf1000000, versions 0x682, 0x1, 0xa, 0x1,
0x0, additional addresses: 0xf1800000 0xf6000000
12. Dino PCI Bridge (13) at 0xf2000000, versions 0x680, 0x2, 0xa, 0x0,
0x0, additional addresses: 0xf2800000
13. U2-IOA BC Runway Port (12) at 0xfff88000, versions 0x580, 0xf, 0xb,
0x1, 0x50
14. U2-IOA BC Runway Port (12) at 0xfff8a000, versions 0x580, 0xf, 0xb,
0x1, 0x50
15. Raven U 200 (9000/780/C200) (0) at 0xfffa0000, versions 0x59d, 0x0,
0x4, 0x0, 0x81
16. Raven U 200 (1) at 0xfffb1000, versions 0x5d, 0x0, 0x9, 0x0, 0x0
That's a total of 16 devices.
CPU(s): 1 x PA8200 (PCX-U+) at 200.000000 MHz
Kernel command line: root=/dev/sda3 HOME=/ console=ttyS0 TERM=vt102
Console: colour dummy device 160x64
Calibrating delay loop... 398.95 BogoMIPS
Memory: 255236k available
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
Dino version 3.0 (bridge mode) found at 0xf2000000
The GSCtoPCI (Dino hrev 2) bus converter found may exhibit
data corruption. See Service Note Numbers: A4190A-01, A4191A-01.
Systems shipped after Aug 20, 1997 will not exhibit this problem.
Models affected: C180, C160, C160L, B160L, and B132L workstations.
Lasi version 0 at 0xffd00000 found.
LED display at ffd0c000 registered
PS/2 keyboard controller at 0xffd08000 (irq 133) found, no device attached.
PS/2 psaux controller at 0xffd08100 (irq 133) found, no device attached.
sticonsole_init: searching for STI ROMs
ccio found U2 I/O MMU at 0xfff88000
io_io_high: 0xf6000000 io_io_low: 0xf2000000
ccio found U2 I/O MMU at 0xfff8a000
ccio: Cujo 2.0 bug needs a work around
io_io_high: 0xf2000000 io_io_low: 0xf1000000
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
request_module[parport_lowlevel]: Root fs not mounted
lp: driver loaded but no devices found
RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize
loop: enabling 8 loop devices
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at iomem 0xffd05800 (irq = 154) is a 16550A
ttyS01 at iomem 0xf2003800 (irq = 74) is a 16550A
Generic RTC Driver v1.02 05/27/1999 Sam Creasey (sammy@oh.verio.com)
Linux Tulip driver version 0.9.13 (January 2, 2001)
eth0: Digital DS21143 Tulip rev 48 at 0xff00, 00:60:B0:7D:D8:67, IRQ 64.
eth0: MII transceiver #1 config 1000 status 7809 advertising 01e1.
parport_init_chip: initialize bidirectional-mode.
parport0: PC-style at 0xffd02800, irq 152 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 19, function 0
sym53c8xx: setting PCI_COMMAND_IO PCI_COMMAND_MEMORY...
sym53c8xx: setting PCI_COMMAND_MASTER...(fix-up)
sym53c8xx: 53c875 detected
sym53c875-0: rev 0x4 on pci bus 0 device 19 function 0 irq 67
sym53c875-0: NCR clock is 40401KHz
sym53c875-0: ID 7, Fast-20, Parity Checking
sym53c875-0: on-chip RAM at 0xf2ffe000
sym53c875-0: restart (scsi reset).
sym53c875-0: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx - version 1.6b
sim700: Configuring 53c710 (SCSI-ID 7) at ffd06100, IRQ 150, options 0
scsi1: Revision 0x2
scsi1: test 1 completed ok.
scsi1 : LASI/Simple 53c7xx
Vendor: SEAGATE Model: ST31230N Rev: HP04
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi1, channel 0, id 6, lun 0
SCSI device sda: 2051460 512-byte hdwr sectors (1050 MB)
Partition check:
sda: sda1 sda2 sda3 sda4
Lasi Harmony Audio rev. 16 at 0xffd04000, using IRQ 146
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
IP-Config: Incomplete network configuration information.
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
INIT: version 2.78 booting
Loading /etc/console/boottime.kmap.gz
Activating swap...
Adding Swap: 124800k swap-space (priority -1)
Checking root file system...
Parallelizing fsck version 1.20 (25-May-2001)
/dev/sda3: clean, 2529/24480 files, 48019/97630 blocks
Calculating module dependencies... done.
Loading modules:
Checking all file systems...
Parallelizing fsck version 1.20 (25-May-2001)
/dev/sda4: clean, 4658/99232 files, 15277/198280 blocks
Setting kernel variables.
Mounting local filesystems...
/dev/sda4 on /usr type ext2 (rw)
Cleaning: /etc/network/ifstate.
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces: done.
]R
Setting the System Clock using the Hardware Clock as reference...
System Clock set. Local time: Sun Nov 4 14:41:36 EST 2001
Cleaning: /tmp /var/lock /var/run.
Initializing random number generator... done.
Recovering nvi editor sessions... done.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd.
Starting kernel log daemon: klogd.
Starting internet superserver: inetd.
Starting deferred execution scheduler: atd.
Starting periodic command scheduler: cron.
Now it really is out-to-lunch and pulling the AC is the only way I know to
shut it down.
Regards, Herb