[parisc-linux] Many experiments on 720, but `init' fails !!
Jeff Arthur
jeffa@mustain.demon.co.uk
Sun, 8 Apr 2001 23:01:43 +0100
<FontFamily><param>Courier New</param>It seems like I have very similar problems with
a HP apollo series 700 (9000/730)
I have tried many builds, with home built cross
compilers, downloaded cross compilers, images
from CDs, downloaded lifs, roots on CDs,
ramdisks and nfsroots. booting using rbootd
over the lan, and off the .iso cd. I always
seem to end up with a variation of the
<color><param>0100,0100,0100</param>break 0,0: pid=1 command='init'
problem.
Am keen to help (If I can, though just a lowly
Sys Admin, not a kernel hack sadly)
P.S. i note that the boot only saw 1 cpu, even
though the box is reported to be a 3 way, I
presume this is as SMP is not compliled in by
default?
here is capture from my console port
(c) Copyright. Hewlett-Packard Company. 1991.
All rights reserved.
PDC ROM rev. 2.1
IODC ROM rev. 2.1
32 MB of memory configured and tested.
Searching for Potential Boot Devices.
To terminate search, press and hold the ESCAPE key.
Device Selection Device Path Device Type
----------------------------------------------------------------------------
P0 scsi.6.0 QUANTUM PD425S
P1 scsi.5.0 QUANTUM PD425S
P2 scsi.4.0 TOSHIBA CD-ROM XM-3701TA
P3 scsi.2.0 HP 2213A
P4 lan.00001c-030853.0.0 burner
b) Boot from specified device
s) Search for bootable devices
a) Enter Boot Administration mode
x) Exit and continue boot sequence
?) Help
Select from menu: b
Enter boot selection, (h)elp, or e(x)it: p4
Trying lan.00001c-030853.0.0
Boot path initialized.
Attempting to load IPL.
Hard booted.
palo ipl root@hetfield Sun Apr 8 19:24:31 UTC 2001
0/vmlinux 2561817 bytes @ 0x6800
0/palo-cmdline '0/vmlinux HOME=/ TERM=linux root=/dev/ram initrd=0/ramdisk console=ttyS0'
0/ramdisk 870400 bytes @ 0x277f19
Kernel: partition 0 file /vmlinux
Ramdisk: partition 0 file /ramdisk
ELF32 executable
Entry 00100000 first 00100000 n 5
Segment 0 load 00100000 size 1469208 mediaptr 0x1000
Segment 1 load 00268000 size 181976 mediaptr 0x168000
Segment 2 load 00298000 size 222280 mediaptr 0x195000
Segment 3 load 002d0000 size 8192 mediaptr 0x1cc000
Segment 4 load 002fef68 size 74720 mediaptr 0x1cef68
Loading ramdisk 870400 bytes @ 01f1a000...
branching to kernel entry point 0x00100000
PDC Console Initialized
Linux version 2.4.0 (root@hetfield) (gcc version 2.97 20010203 (experimental)) #1 Sun Apr 8 19:16:06 UTC 2001
FP[0] enabled: Rev 3 Model 0
The 32-bit Kernel has started...
Determining PDC firmware type: Older Legacy Box
setup_cmdline(0x64d58,0x64d58,0x1f1a000,0x1fee800)
PALO command line: 'HOME=/ TERM=linux root=/dev/ram console=ttyS0'
PALO initrd 1f1a000-1fee800
model 00002020 00000481 00000000 00000000 3a238470 000011f4 00000004 0000000d 00000000
vers 00000003
CPUID vers 0 rev 0
model 9000/730
Total Memory: 32 Mb
initrd: 11f1a000-11fee800
pagetable_init
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Searching for devices...
Found devices:
1. Coral SGC Graphics (10) at 0xf8000000, versions 0x4, 0x0, 0x77, 0x0, 0x0
2. Cobra Core BA (11) at 0xf082f000, versions 0x4, 0x0, 0x70, 0x0, 0x0
3. Cobra Core SCSI (10) at 0xf0825000, versions 0x4, 0x0, 0x71, 0x0, 0x0
4. Cobra Core LAN (802.3) (10) at 0xf0826000, versions 0x4, 0x0, 0x72, 0x0, 0x0
5. Cobra Core HIL (10) at 0xf0821000, versions 0x4, 0x0, 0x73, 0x0, 0x0
6. Cobra Core RS-232 (10) at 0xf0823000, versions 0x4, 0x0, 0x75, 0x0, 0x0
7. Cobra Core RS-232 (10) at 0xf0822000, versions 0x4, 0x0, 0x75, 0x0, 0x0
8. Cobra Core Centronics (10) at 0xf0824000, versions 0x4, 0x0, 0x74, 0x0, 0x0
9. Cobra EISA BA (11) at 0xfc000000, versions 0x4, 0x0, 0x76, 0x0, 0x0
10. King Cobra (730) (0) at 0xfffbe000, versions 0x202, 0x0, 0x4, 0x0, 0x81
11. Cobra (1) at 0xfffbf000, versions 0x13, 0x0, 0x9, 0x0, 0x0
That's a total of 11 devices.
CPU(s): 1 x PA7000 (PCX-S) at 66.000000 MHz
Kernel command line: HOME=/ TERM=linux root=/dev/ram console=ttyS0
Calibrating delay loop... 65.74 BogoMIPS
Memory: 29156k available
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
ASP version 1 at 0xf0800000 found.
LED (ASP-style) display at f0800020 registered
Found HIL at 0xf0821000, IRQ 94
HIL: keyboard found at id 0
Found i82596 at 0xf0826000, IRQ 87
early initialization of device eth0 is deferred
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
lp: driver loaded but no devices found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
82596.c: MAC of HP700 LAN blindely read from the prom!
eth0: Couldn't get consistent shared memory
eth0: 82596 at 0xf0826000, 08 00 09 19 1B 34 IRQ 87.
82596.c $Revision: 1.17 $
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 850 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at iomem 0xf0823800 (irq = 90) is a 16550A
ttyS01 at iomem 0xf0822800 (irq = 89) is a 16550A
Generic RTC Driver v1.02 05/27/1999 Sam Creasey (sammy@oh.verio.com)
parport_init_chip: enhanced parport-modes not supported.
parport0: PC-style at 0xf0824800, irq 88 [PCSPP]
lp0: using parport0 (interrupt-driven).
SCSI subsystem driver Revision: 1.00
sim700: Couldn't get consistent shared memory
sim700: Configuring 53c700 (SCSI-ID 7) at f0825100, IRQ 86, options 1
scsi0: Revision 0x0
Post test1, istat 05, sstat0 00, dstat 84
sim700: WARNING IRQ probe failed, (returned 0)
scsi0: WARNING: target data areas are not dma coherent!
scsi0: test 1 completed ok.
scsi0 : LASI/Simple 53c7xx
Vendor: HP Model: 2213A Rev: C023
Type: Direct-Access ANSI SCSI revision: 01 CCS
Vendor: TOSHIBA Model: CD-ROM XM-3701TA Rev: 0236
Type: CD-ROM ANSI SCSI revision: 02
Vendor: QUANTUM Model: PD425S Rev: 535A
Type: Direct-Access ANSI SCSI revision: 02
Vendor: QUANTUM Model: PD425S Rev: 535A
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 2, lun 0
Detected scsi disk sdb at scsi0, channel 0, id 5, lun 0
Detected scsi disk sdc at scsi0, channel 0, id 6, lun 0
SCSI device sda: 1296512 512-byte hdwr sectors (664 MB)
Partition check:
sda: unknown partition table
SCSI device sdb: 833150 512-byte hdwr sectors (427 MB)
sdb: unknown partition table
SCSI device sdc: 833150 512-byte hdwr sectors (427 MB)
sdc: unknown partition table
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 4, lun 0
Uniform CD-ROM driver Revision: 3.12
linear personality registered
raid0 personality registered
raid1 personality registered
raid5 personality registered
raid5: measuring checksumming speed
8regs : 41.910 MB/sec
8regs_prefetch: 53.721 MB/sec
32regs : 42.672 MB/sec
32regs_prefetch: 54.483 MB/sec
raid5: using function: 32regs_prefetch (54.483 MB/sec)
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
eth0: link ok.
Sending BOOTP requests.... OK
IP-Config: Got BOOTP answer from 0.0.0.0, my address is 192.168.1.201
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem).
break 0,0: pid=1 command='init'
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00000000000001000000000000001111
r0-3 00000000 1028260c 102d0000 00000000
r4-7 102d0580 1028260c 102d0000 00000000
r8-11 102d0580 00000000 00000000 1014ab60
r12-15 00000000 00000000 00000000 00000000
r16-19 11ff8000 1028260c 102d0000 00000000
r20-23 102d0580 00000000 00000000 00000000
r24-27 faf00038 faf0004c 00000001 10139494
r28-31 00000000 00000000 faf00080 00002f13
sr0-3 1ff2d60 11eef0c0 00000000 0000ffff
sr4-7 0000001 00000001 00000001 00000001
IASQ: 0000001 00000001 IAOQ: 00002f13 00002f17
IIR: 000000 ISR: 00000001 IOR: 00000000
ORIG_R28: 40800000
break 0,0: pid=1 command='init'
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00000000000001000000000000001111
etc.....</color>
<nofill>
Thought for the Day:
Fax is stranger than fiction.